By combining the technological expertise and innovation of Panduit connectivity and Prysmian Group (who acquired General Cable in 2018) cabling products, PanGen Structured Cabling Solutions provide a wide range of world-class copper and fiber solutions to support all of your needs. Their combined Category 6A, 6 and 5e high-performance copper and fiber systems with network connectivity and cables provide a robust and optimized cabling infrastructure that exceeds all current and future electrical parameters.

PanGen® Category 6A System Solutions

PREMIUM

GenSPEED® 10 MTP™ Category 6A Cable

TX6A™ 10Gig UTP Patch Cords

Category 6A/Class EA, UTP patch cords shall be constructed of 24 AWG solid copper cable with an enhanced performance modular plug on each end. Copper conductors in patch cable shall be twisted in pairs and separated by a quadrant separator. All four pairs shall be surrounded by solid foil tape and a flame retardant jacket. The tape shall suppress alien crosstalk and allow 10 Gb/s transmission. Patch cord cable shall be offered in multiple colors and lengths for design flexibility with a strain relief boot on each modular plug. All patch cords shall be compatible with both T568A and T568B wiring schemes.

TX6A™ Cat 6A UTP Field Term RJ45 Plug

The TX6A™ Category 6A UTP Field Term RJ45 Plug is a simple-to-attach plug for field termination of 4-pair unshielded twisted pair cable. Providing Category 6A performance the TX6A™ plug is also compatible with Category 6 and 5e systems. The two-piece straight and up/down angled TX6A™ plug terminates 4-pair, 22 - 26 AWG, 100 ohm unshielded twisted pair cable and uses proven TG-style forward motion termination technology to optimize performance by maintaining cable pair geometry while eliminating conductor untwist.

DP6A™ 10Gig Punchdown Patch Panels

Category 6A/Class EA, punchdown patch panels shall terminate 4-pair, 22 – 26 AWG, 100 ohm unshielded twisted pair cable with an industry standard single wire 110 punchdown tool. Patch panels shall include a universal label coded for T568A and T568B wiring schemes and mount to 19 inches and 23 inches racks. Patch panels shall be easy to identify with pre-printed numbers, write-on areas and optional label kits. The DP6A 10Gig Punchdown Patch Panel must be installed as part of the TX6A™ 10Gig UTP Copper Cabling System to achieve IEEE 10GBASE-T certified performance.

PanGen® Category 6A System Solutions

SHIELDED

GenSPEED® 10,000 Category 6A

F/UTP (ScTP) Cable

TX6A™ 10Gig Shielded Patch Cords

Category 6A/Class EA, S/FTP patch cords shall be constructed of 26 AWG shielded twisted pair stranded copper cable with an enhanced performance shielded modular plug at each end. Patch cord cable shall be offered in multiple colored S/FTP cable for design flexibility with a black strain relief boot on each modular plug. All patch cords shall be compatible with both T568A and T568B wiring schemes.

Mini-Com TX6A™ 10Gig Shielded Jack Modules

Category 6A/Class EA, 8-position, shielded jack module shall terminate 4-pair, 22 – 26 AWG, 100 ohm shielded twisted pair cable and shall not require a punchdown tool. Shielded jack modules shall use a forward motion termination method to optimize performance by maintaining cable pair geometry while eliminating conductor untwist. The termination cap shall be color-coded blue to designate Category 6A performance and shall include a universal label coded for T568A and T568B wiring schemes. The Mini-Com TX6A 10Gig Shielded Jack Module must be installed as part of the TX6A 10Gig Shielded Copper Cabling System to achieve IEEE 10GBASE-T certified performance.

Mini-Com All Metal Shielded Modular Patch Panels

All metal modular patch panels shall be made of stainless steel and mount to standard racks and cabinets. All metal patch panels shall accept all Mini-Com® Shielded Jack Modules for shielded installations. Patch panel write-on areas and optional adhesive labels shall identify each port and panel. Angled all metal modular patch panels shall be available in standard density 24 and 48-ports. Flat all metal modular patch panels shall be available in standard density 24 and 48-ports. Flat design in 24 and 48-ports shall also be available with built-in strain relief bar with unique features to support individual cables.

PanGen® Category 6 System Solutions

ENHANCED

GenSPEED® 6500 Enhanced Category 6 Cable

TX6-28™ Cat6 Performance 28 AWG UTP Patch Cords

Category 6/Class E, UTP, small diameter patch cords are constructed of 28 AWG, unshielded, twisted pair, stranded copper (dual-rated CM/LSZH) cable with high performance RJ45 modular plugs. Patch cords are offered in multiple lengths and colors for design flexibility.

Mini-Com TX6™ PLUS UTP Jack Modules

Category 6/Class E, 8-position, UTP jack module shall terminate 4-pair, 22 – 26 AWG, 100 ohm unshielded twisted pair cable and shall not require a punchdown tool. UTP jack modules shall use a forward motion termination method to optimize performance by maintaining cable pair geometry while eliminating conductor untwist. The termination cap shall be color coded white to designate Category 6 performance and shall include a universal label coded for T568A and T568B wiring schemes.

DP6™ PLUS Punchdown Patch Panels

Category 6/Class E, punchdown patch panels shall terminate 4-pair, 22 – 26 AWG, 100 ohm unshielded twisted pair cable with an industry standard single wire 110 punchdown tool. Patch panelsshall include a universal label coded for T568A and T568B wiring schemes and mount to 19 inches and 23 inches racks. Patch panels shall be easy to identify with pre printed numbers, write-on areas and optional label kits.

Singlemode

GenSPEED® Singlemode Optical Fiber Cable

LC OptiCam Pre-Polished Fiber Optic Connectors

LC OptiCam® Pre-Polished Connectors with rear pivot latch shall be ANSI/TIA-604-FOCIS-10 compatible and contain a factory-terminated fiber, eliminating field polishing and adhesive. LC pre-polished connectors shall have an average insertion loss of 0.3dB per mated pair for multimode and singlemode fiber. LC pre-polished connectors shall captivate fiber and buffer in one action allowing for up to two re-terminations with no degradation in performance.

Opticom Fiber Adapter Panels

Fiber adapter panels contain TIA/EIA-604 FOCIS compliant or compatible simplex or duplex fiber optic adapters and meet or exceed TIA/EIA-568-C.3 requirements. Fiber adapter panels include horizontal and vertical MPO adapters, LC, keyed LC, and SC fiber optic adapters. Fiber optic adapters include zirconia ceramic split sleeves to fit specific network requirements. LC and SC adapter housing colors follow the TIA/EIA-568-C.3 suggested color identification scheme. Multimedia modular panels allow customization of installation for applications requiring integration of fiber optic and copper cables. Blank fiber adapter panels reserve fiber adapter panel space for future use. All fiber adapter panels snap quickly into the front of fiber optic patch panels and enclosures for easy network deployment or moves, adds, and changes.

Opticom Rack Mount Fiber Enclosures

Rack mount fiber enclosures shall house, organize, manage and protect fiber optic cable, terminations, splices, connectors and patch cords. Enclosure shall accommodate all Panduit trunk cables, connectors, patch cords, fiber adapter panels (FAP). The enclosure shall include integral cable management and bend radius control for transition to vertical cable managers. Fiber optic enclosures shall be constructed of steel material. Molded front and back doors shall be removable for cabling and connector installation. 1 RU and 2 RU enclosures shall provide full front and rear access with a drawer that slides forward and backward. 4 RU enclosures shall feature a fixed bulkhead design. Enclosure shall have multiple knockouts for a variety of trunk cable entry points.

Multimode

GenSPEED® OM2/OM3/OM4/OM5 Optical Fiber Cable

Opti-Core Fiber Optic Patch Cords and Pigtails

The Opti-Core® patch cords support network applications in main, horizontal and equipment distribution areas and are available in riser (OFNR) and low smoke zero halogen (LSZH) rated jacket materials. In addition, pre-terminated fiber optic pigtails support fusion splice field termination applications.

Both fiber optic patch cords and pigtails are available in OM1, OM3, OM4, OM4+, OM5 and OS2 fiber types to meet the demands of Gigabit Ethernet, 10 Gigabit Ethernet and high speed Fibre Channel.

OptiCam 2 Termination Tool

The OptiCam® 2 Termination Tool offers a step by step visual guidance and insertion loss calculation to ensure the field fiber and fiber stub are in proper alignment before camming. This allows even the less experienced technicians to terminate fiber with confidence. A simple, ergonomic and symmetrical design allows for left or right-handed termination in both handheld and benchtop orientations.